Photo Cell Protect 800 Wireless Loud Bell Kit

Photo Cell Protect 800 Wireless Loud Bell Kit supplied with an Outdoor Wireless Receiver & Loud Ringing Bell. Ideal for applications across Warehouse, Factory & Gate Entrances (if power is available on one side).

It also works in conjunction with all other Protect-800 Receivers & Transmitters. 

The kit is supplied with the following:

• 1 x Protect-800 Wireless Transmitter (mounted inside a weatherproof box).
• 1 x set of Weatherproof Photo Cells.
• 1 x Outdoor Weatherproof Receiver.
• 1 x Weatherproof Bell.
• 2 x 3 -pin Plug in Transformers.

The Wireless Transmitter has a working range back to the Receiver of 800 metres (line of sight), which equates to around 400 - 600 metres in most applications.

How it Works !!

The weatherproof Photo Cells are supplied as a pair which need to be mounted either side of a suitable Entrance in a position where they are facing each other (maximum distance 12 metres), one Photo Cell is powered by the Plug in Transformer (supplied), whilst the second Photo Cell is powered by a Battery (supplied) for easier Installation.

Connected to the powered Photo Cell (by 3 metres of cable) is a Battery powered Transmitter (mounted inside a weatherproof box), which will send a Wireless signal to the Outdoor Receiver when the Photo Cell Beams are triggered.

Additional Indoor & Outdoor Receivers can also be added (no limit).

A unique Wireless Commercial Bell Alert !!

Please Contact Us for any Advice !!

Outdoor Receiver:

• 1 x Outdoor Receiver (P800-WSR/1).
• 1 x Remote Control (P800-WSK/1).
• 1 x 12v DC Plug in Power Supply.
• 2 x AAA Batteries.
• 1 x 12v Weatherproof Bell.

Photo Cell Kit:

• 1 x Set of Photo Cells & Battery.
• 1 x Protect-800 Transmitter & Battery (inside a weatherproof box).
• 1 x 3-pin Plug in Transformer (2-pin available upon request).

Outdoor Receiver:

Receiver:

• Weatherproof: Yes.
• Power Supply: 12v 5 amp DC.
• Weatherproof Cable Entry Glands: Yes.
• Channels: 2.
• Sensors per Channel: 4.
• Operating Range: 800 metres (line of sight).
• Arming & Disarming Method: Remote Control.
• 12v DC Outputs: 2.
• Output Duration:
• • 1 second or minute.
  • 3 seconds or minutes.
  • 10 seconds or minutes.
  • 15 seconds or minutes.
  • 20 seconds or minutes.
  • 30 seconds or minutes.
  • Latched ON (until disarmed using the remote control).
• Duration Selection: Internal Dip-switches.
• Frequency: 869.400 – 869.650 MHz.
• Size: 170 x 125 x 60 mm.

Remote Control:

• Operation:
• Channel 1 Arm, Disarm & SOS.
• Channel 2 Arm, Disarm & SOS.
• Power Supply: 2 x AA Batteries (supplied).
• Size: 85 x 40 x 25 mm.
• Transmission Range: 800 metres (line of sight).
• Multiple Remote Control Operation: Yes (no limit).
• Feedback Indicator: Yes (it confirms a successful operation).
• Frequency: 869.400 – 869.650 MHz.
• Wall Bracket: Yes (supplied).

Bell:

• Power Supply: 12v DC.
• External: Yes.
• Size: 150 mm Diameter x 60 mm Deep.
• Mounting Bracket: 4 x Holes.
• Volume: Approx 85 Db.

Photo Cell Kit:

Photo Cells:

• Working Voltage: 12~24VAC/DC or 3V Dry Battery.
• Working Current(24VDC):emitter: =8mA receiver: =40mA.
• Photocell Wavelength: 940nm.
• Angle of opposite emission: =±5º.
• Receiver range: =12m.
• Internal Rotation system adjusted Angle: 0~180 º.
• Working temperature: -20º~+60?.
• Relay contact loading capacity: 1A/30VDC.
• Waterproof grade: IP54.
• Size: 128*50*28mm.

Transmitter:

Wireless Transmitter:

• Wireless Range: 800 metre (line of sight).
• Power Supply: 1 x 3v Lithium CR123A Battery.
• Battery Life: 12 - 18 months (most applications).
• Size: 65 x 33 x 15 mm.
• Activation Methods:
• Wired Input: Yes (N/O or N/C Momentary Volt Free, when used as a circuit board).

Mounting Box:

• Material: Plastic.
• Weatherproof: IP65.
• External Size: 150 (L) x 85 (W) x 34 (D) mm.
• Internal Size: 106 (L) x 76 (W) x 28 (D) mm.
• Label: V range.

Transformer:

• Voltage: 12v DC.
• Output: 1 amp.
• Cable Length: 3 metres.
• Pin Type: 3-pin UK (2-pin available upon request).