DA600+ Siren & 2B Beams, Fully Solar Powered Wireless Perimeter Alarm System

This unique Long Range Wireless DA600+ Perimeter Alarm consists of a set of 2B Wireless Perimeter Beams & Wireless Solar Siren with Bright Flashing Strobe Light, therefore no power is required on site at all, ideal for Remote locations.

The system is Armed & Disarmed using Remote Controls from up to 100 metres away, and can be used as an:

• Outdoor Alarm (intruder passes through the beams and the Solar Siren will activate together with the built in Flashing Strobe Lights).
• Outdoor Alert (a visitor passes through the beams and the siren will chime and flash for a few seconds, ideal for when you are working around the buildings).

You can also add additional Solar Perimeter Beams (various sizes), additional Solar Sirens and Internal Wireless Receivers to suit most applications !! 

Compatible with all DA600+ products !!

Solar Siren:

The quality Solar Powered Siren & Bright Flashing LED Strobe Lights communicates directly with the 1B-100 Wireless Beams (supplied) together with any further Beams or Sensors you wish to add.

The Siren doubles up as the control panel and is Armed & Disarmed using a Remote Control from up to 100 metres away, the Siren can be programmed to operate in two ways (but you can only use a single chosen program mode):

• Alarm (in this mode once the Siren is Armed it will trigger a 100 Decibel Siren together with very bright Flashing LED Strobe Lights should any Detectors being activated).
• Alert (this mode will omit a 6 second Siren & Flashing Strobe, designed to be a visitor Alert for businesses where staff are working outside in a yard etc).

It is fitted onto a wall using a simple mounting bracket, it would be best to be fitted on a South facing wall if possible.

Operating Range:

The Wireless operating range between the Beams & Siren is 900 metres (line of sight) which can be doubled by using the signal repeater (part number 004-2910), the Detection range is up to 100 metres.

You can use up to 32 sets with the Solar Wireless Siren, you can mix & match by using a selection of different sizes of Beams or Sensors within this single system.

You can also add the one or more Internal Receivers (part number 004-2880) should you need notification inside the House or Office.

Siren:

• 1 x Solar Powered Siren & Flashing Strobe Light.
• 1 x Wall Bracket.
• 2 x Remote Controls. 

Detector Beams:

• 1 x Set of 2B Solar Powered Detecting Beams.
• 1 x Set of Wall Mounting Brackets. 
• 1 x Set of Pole Mounting Brackets.
• 1 x Set of Instructions.  

Siren:

• Size: 280 x 180 x 74 mm.
• Siren Options:
• Loud 4 second chime.
• Full Siren & Flashing Strobe (duration 1 minute).
• Siren Level: 90 decibel Chime mode, 110 decibel Siren mode.
• LED Illumination: 70 lm.
• Wireless Working Range to Remote Control: over 100 metres (line of sight).
• Wireless Working Range to Perimeter Beams: 900 metres (line of sight).
• Mounting Method: Rear Plate.
• Built in Battery: 3000mAH 6.4v.
• Battery Type: Lithium.
• Frequency: 433 MHz.
• Working Temperature: -30 - +70.

Beams:

• Beam Size: 590 (H) x 123 (W) x 45 (D) mm.
• Power Supply: Re-chargeable AA Batteries.
• Charging Method: Built in Solar Panels.
• Mounting Methods: Wall or Pole.
• Detection Range: 100 metres.
• Transmission Range: 900 metres (line of sight).
• Frequency: 433 Mhz.
• IP Rating: IP66.
• Distance Between Detection Beams: 60mm.
• Number of Beams: 2 sets.
• Charging Port: 9 - 12v DC (500 m/A to 1 amp).
• Built in Buzzer: Yes (turn on with 1 - 6 presses of button, off 7 or 8 times).
• Buzzer OFF (7 with immediate reset, 8 with 3 minutes battery saving reset).

Easy Programming Method:

1. Turn On Beams (switch on rear).
2. Mount the Beams.
3. Line up By Eye, String Line etc.
4. Put the relevant Receiver into Learn Mode.
5. Walk through the Beams, at this time (providing you have them correctly lined up), a low red glow will illuminate briefly.
6. The Signal sent to the Receiver from this set of beams will be learned into the relevant receiver.
7. Take the Receiver out of learn mode.
8. The system is now ready.